Parser -av

anyone?

Err
emerge XML-Parser -av

emerge XML-Parser, and probably file a bug report if it’s a missing dependency

What sound hardware do you have?

emerge XML-Parser -av
err
what carebear said

CareBear\, audigy2

anyone know where I can go to talk about a freetype issue?

IRQ problem?

when you delete something from an NTFS volume in linux, where do the files go? .. I deleted a bunch of files on my ntfs partition but didnt see an increase in free space..

#freetype ?

empty

CareBear\, i don’t think so …cause i get sound, i just get a crackling that gets really annoying.

I was hoping maybe some sort of generic linux programming channel

Like distortion?
Check the mixer levels?

anything in particular i need to look for?

Maybe internal amps are on max, they usually don’t handle clipping very well.

re-emerged XML-Parser. that seemed to do the trick, thanks

Run alsamixer and if it doesn’t show dB values for each control emerge alsa-utils – make sure all levels are = 0.00 dB

what if the driver finds your card but claims that there is no codec

can anyone hear me?!?!?!?!?!?!?!?!?????????????????

no

ok, thx

Please file that bug for the ebuild.

ok

If I install gentoo from the LiveCD, can I run an Active Directory server through Samba out of the box (of course, having to change stuff in samba.conf)

you can

got sound working but i can’t test, lol
what should i emerge to get mp3, avi, wmv, etc support?

eth3r3al, if you install the correct packages and configure it correctly

Even a PDC?

CareBear\: even a PDC.

what packages would i need?

emerge mplayer IMO

CareBear\, should I set them all to max?

aha

Make sure none are above 0.00 dB

so db gain = 0.00 ?

eth3r3al, http://gentoo-wiki.com/Samba

Yep!
Also read up on the Samba documentation. There’s a good .pdf with a few 100 pages.

I ran rc-update del net.eth0 but still dhcpcd or what ever still starts it. What can I do to completely remove eth0 from my system and tell it to use eth1?

Nice. I’ve only done member servers.

wiki skkane emerge mplayer

thank you!

http://gentoo-wiki.com/HOWTO_Emerge_MPlayer

It’s better if you make udev set up the device names right.

CareBear\: you can’t do a 2003 AD, just NT4, but it is fully doable.

CareBear\: I don’t think i will live long enough to read all of that

Oh but the question was AD.

that is samba for you.

NT4 PDC I’ve done plenty.

ugh
I swear so violently against my service provider

Too bad. You should read it.

CareBear\, done …I still get a little static.

CareBear\: 2003 AD doesn’t have PDCs…

so how do I tell udev to use eth1 rather then eth0?

CareBear\: is there anyway to pull in dependencies to specific useflags rather than erroring out?

Ok, but the equivalent?

CareBear\: If i ever get the urge to burn my eyes out of my skull with a monitor, i will

Hmm, have you tried using built_with_use also in DEPEND ?

mzbot, tkz

CareBear\: it doesn’t really have equivalents. It is a peer-peer set-up. There are 5 roles which can only be fulfilled by one server, but they are not special in anyway other than that.

reisio, tkz i mean

CareBear\: is that possible?

what’s the command for adding a user to a group again?

Ok. I know it needs a Kerberos realm and a DNS at least, but I have intentionally stayed far away from AD.
Try it and let me know?

CareBear\: 2003 AD is a pain to run in a heterogenous enviroment. You can run samba member servers, but not domain controllers (at least, not samba3 DCs.)

eth0 is my firewire card but I don’t want it acting as network card I want eth1 that is my real network card. How do I tell udev to use eth1 rather then eth0?

Right.
Look in /etc/udev/rules.d/70-persistent-net.rules
If you have ip over 1394 enabled in kernel you will get a networking interface for your fw card.

gpasswd with some option

edit /etc/udev/rules.d/70-persistent-net.rules and switch the eth# allocation

But change which gets what name in the files.
s/files/rules file/

thanks

ARGH this P3-650 is not enough
4.28, 3.43, 3.13

Is there a package for KDE 4 beta?

CareBear\: Not bad, I tend to arvage at 7 on an AMD DualCore 5000+

nothing about eth0 is in that file. where else can I look? I looked in 95-net.rules and it talks about net.sh but where is net.sh?

Perhaps you need an udev upgrade?
I would too if I was running all the catalysts that I want to.

pastebin the 70*net* file please

Ah what Miravlix said.